Debugging a mysterious terminal setting (Shallow Thoughts)

Akkana's Musings on Open Source Computing and Technology, Science, and Nature.

Thu, 28 Aug 2014

Debugging a mysterious terminal setting

For the last several months, I repeatedly find myself in a mode where my terminal isn't working quite right. In particular, Ctrl-C doesn't work to interrupt a running program. It's always in a terminal where I've been doing web work. The site I'm working on sadly has only ftp access, so I've been using ncftp to upload files to the site, and git and meld to do local version control on the copy of the site I keep on my local machine. I was pretty sure the problem was coming from either git, meld, or ncftp, but I couldn't reproduce it.

Running reset fixed the problem. But since I didn't know what program was causing the problem, I didn't know when I needed to type reset.

The first step was to find out which of the three programs was at fault. Most of the time when this happened, I wouldn't notice until hours later, the next time I needed to stop a program with Ctrl-C. I speculated that there was probably some way to make zsh run a check after every command ... if I could just figure out what to check.

Terminal modes and stty -a

It seemed like my terminal was getting put into raw mode. In programming lingo, a terminal is in raw mode when characters from it are processed one at a time, and special characters like Ctrl-C, which would normally interrupt whatever program is running, are just passed like any other character.

You can list your terminal modes with stty -a:

$ stty -a
speed 38400 baud; rows 32; columns 80; line = 0;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = ;
eol2 = ; swtch = ; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R;
werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0;
-parenb -parodd cs8 -hupcl -cstopb cread -clocal -crtscts
ignbrk -brkint ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl -ixon -ixoff
-iuclc -ixany -imaxbel iutf8
opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0
-isig icanon -iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt
echoctl echoke

But that's a lot of information. Unfortunately there's no single flag for raw mode; it's a collection of a lot of flags. I checked the interrupt character: yep, intr = ^C, just like it should be. So what was the problem?

I saved the output with stty -a >/tmp/stty.bad, then I started up a new xterm and made a copy of what it should look like with stty -a >/tmp/stty.good. Then I looked for differences: meld /tmp/stty.good /tmp/stty.bad. I saw these flags differing in the bad one: ignbrk ignpar -iexten -ixon, while the good one had -ignbrk -ignpar iexten ixon. So I should be able to run:

$ stty -ignbrk -ignpar iexten ixon
and that would fix the problem. But it didn't. Ctrl-C still didn't work.

Setting a trap, with precmd

However, knowing some things that differed did give me something to test for in the shell, so I could test after every command and find out exactly when this happened. In zsh, you do that by defining a precmd function, so here's what I did:

precmd()
{
    stty -a | fgrep -- -ignbrk > /dev/null
    if [ $? -ne 0 ]; then
        echo
        echo "STTY SETTINGS HAVE CHANGED \!\!\!\!\!\!\!\!\!\!\!\!\!\!\!\!"
        echo
    fi
}
Pardon all the exclams. I wanted to make sure I saw the notice when it happened.

And this fairly quickly found the problem: it happened when I suspended ncftp with Ctrl-Z.

stty sane and isig

Okay, now I knew the culprit, and that if I switched to a different ftp client the problem would probably go away. But I still wanted to know why my stty command didn't work, and what the actual terminal difference was.

Somewhere in my web searching I'd stumbled upon some pages suggesting stty sane as an alternative to reset. I tried it, and it worked.

According to man stty, stty sane is equivalent to

$ stty cread -ignbrk brkint -inlcr -igncr icrnl -iutf8 -ixoff -iuclc -ixany  imaxbel opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke

Eek! But actually that's helpful. All I had to do was get a bad terminal (easy now that I knew ncftp was the culprit), then try:

$ stty cread 
$ stty -ignbrk 
$ stty brkint
... and so on, trying Ctrl-C each time to see if things were back to normal. Or I could speed up the process by grouping them:
$ stty cread -ignbrk brkint
$ stty -inlcr -igncr icrnl -iutf8 -ixoff
... and so forth. Which is what I did. And that quickly narrowed it down to isig. I ran reset, then ncftp again to get the terminal in "bad" mode, and tried:
$ stty isig
and sure enough, that was the difference.

I'm still not sure why meld didn't show me the isig difference. But if nothing else, I learned a bit about debugging stty settings, and about stty sane, which is a much nicer way of resetting the terminal than reset since it doesn't clear the screen.

Tags: , ,
[ 15:41 Aug 28, 2014    More linux | permalink to this entry | comments ]
(Commenting requires Javascript from ShallowSky.com and Disqus.com, and a cookie from Disqus.com.)
blog comments powered by Disqus

Syndicated on:
LinuxChix Live
Ubuntu Women
Women in Free Software
Graphics Planet
DevChix
Ubuntu California
Planet Openbox
Devchix
Planet LCA2009

Friends' Blogs:
Morris "Mojo" Jones
Jane Houston Jones
Dan Heller
Long Live the Village Green
Ups & Downs
DailyBBG

Other Blogs of Interest:
DevChix
Scott Adams
Dave Barry
BoingBoing

Powered by PyBlosxom.